oc2

CT-832.10
CT-832.10
« 1 од 6 »
Technical Parameters Units CT-832.8 CT-832.10 CT-832.12 CT-932.14 CT-1032.10 CT-1032.12
Height of centers
mm 417 417 417 467 517 517
Swing over bed
mm 830 830 830 930 1030 1030
Swing over cross slide
mm 510 510 510 610 710 710
Swing in gap
mm 1000 1000 1000 1100 1200 1200
Bed width
mm 560 560 560 560 560 560
Distance between centers
mm 1000-1500-2000-3000 4000-5000-6000 1000-1500-2000-3000 4000-5000-6000 1000-1500-2000-3000 4000-5000-6000 1000-1500-2000-3000 4000-5000-6000 1000-1500-2000-3000 4000-5000-6000 1000-1500-2000-3000 4000-5000-6000
Spindle bore
Ømm Ø210 Ø260 Ø315 Ø360 Ø260 Ø315
Spindle nose
DIN55027 №12 №12 №12 №12 №12 №12
Number of speed
No. 12 12 12 12 12 12
Spindle speed range
rpm 8-400 8-400 8-400 8-400 8-400 8-400
Longitudinal feed range
mm/rev 0,039-15 0,039-15 0,039-15 0,039-15 0,039-15 0,039-15
Cross feed range
mm/rev 0.0195-7,5 0.0195-7,5 0.0195-7,5 0.0195-7,5 0.0195-7,5 0.0195-7,5
Metric thread range
mm 0,5-150 0,5-150 0,5-150 0,5-150 0,5-150 0,5-150
Inch thread range
tpi 60-13/64 60-13/64 60-13/64 60-13/64 60-13/64 60-13/64
Module thread range
Module 0,125-37,5 0,125-37,5 0,125-37,5 0,125-37,5 0,125-37,5 0,125-37,5
DP thread range
DP 240-4/5 240-4/5 240-4/5 240-4/5 240-4/5 240-4/5
Cross slide travel
mm 465 465 465 510 550 550
Top slide travel
mm 250 250 250 250 250 250
Quill diameter
mm 125 125 125 125 125 125
Quill travel
mm 265 265 265 265 265 265
Quill taper
Morse 6 6 6 6 6 6
Coolant pump
kW 0.09 0.09 0.09 0.09 0.09 0.09
Rapid traverse
kW 0.55 0.55 0.55 0.55 0.55 0.55
Lubrication pump
kW 0.12 0.12 0.12 0.12 0.12 0.12
Main motor power
kW 15 / 18,5 15 / 18,5 15 / 18,5 15 / 18,5 15 / 18,5 15 / 18,5
  Standard Accessories & Equipment Optional Accessories & Equipment
  Monolith cast iron body and gap
  3-jaw self-centering chuck
  Centralized lubrication system
  4-jaw independent chuck
  Coolant system with pump
  Face plate without jaws
  Low voltage machine lamp 12V
  Follow rest
  Back plate for universal chuck
  Steady rest
  Full length rear splash guard
  Digital Read Out
  Splash guard for the chuck
  One position longitudinal stop
  Hexagonal wrenches set
  Thread chasing dial
  Dead centres for spindle
  Taper turning attachment
  Reduction sleeve
  Drive plate with turnning dogs
  Rapid traverse of the apron in 4 directions
  Live (rotating) centre
  4-positions toolholder with key
  Drill chuck
  Heavy Steady Rest End Support
  Foot brake pedal
  4-jaw Independent  Chuck Both Sides
  Increasing of the main motor power
  Quck chabge tool post MultiFix
  Electro-dynamic brake