Technical Parameters | Units | CU-502 | CU-582 | CU-662 |
Height of centers
|
mm | 260 | 290 | 330 |
Swing over bed
|
mm | 520 | 580 | 660 |
Swing over cross slide
|
mm | 320 | 380 | 380 |
Swing in gap
|
mm | 710 | 770 | 850 |
Bed width
|
mm | 400 | 400 | 400 |
Distance between centers
|
mm | 1000/1500/2000/3000 4000/5000/6000 | 1000/1500/2000/3000 4000/5000/6000 |
1000/1500/2000/3000 4000/5000/6000 |
Spindle bore
|
Ømm | 72/80/104 | Ø72; Ø80; Ø104 | Ø72; Ø80; Ø104 |
Spindle nose
|
DIN55027 | No. 8 (No. 11) | No8, No11 | No8, No11 |
Number of speed
|
No. | 18 | 18 | 18 |
Spindle speed range
|
Ømm | 11,2÷2000 | 11,2-2000 | 11,2-2000(9-1600) |
Longitudinal feed range
|
rpm | 0.039-24 | 0,039-24 | 0,039-24 |
Cross feed range
|
mm/rev | 0.0195-12 | 0.0195-12 | 0.0195-12 |
Metric thread range
|
mm/rev | 0,5-240 | 0,5-240 | 0,5-240 |
Inch thread range
|
mm | 60-1/8 | 60-1/8 | 60-1/8 |
Module thread range
|
tpi | 0,125-60 | 0,125-60 | 0,125-60 |
DP thread range
|
Module | 240-0,5 | 240-0,5 | 240-0,5 |
Cross slide travel
|
mm | 310 | 320 | 360 |
Top slide travel
|
mm | 140 | 140 | 140 |
Quill diameter
|
mm | 75 | 75 | 75 |
Quill travel
|
mm | 250 | 250 | 250 |
Quill taper
|
Morse | 5 | 5 | 5(6) |
Coolant pump
|
kW | 0.09 | 0.09 | 0.09 |
Rapid traverse
|
kW | 0.55 | 0.55 | 0.55 |
Lubrication pump
|
kW | 0.12 | 0.12 | 0.12 |
Main motor power
|
kW | 5,5 (7,5) | 7,5-11 | 11 |
Standard Accessories & Equipment | Optional Accessories & Equipment |
Main Motor
|
3-jaw self-centering chuck
|
Spindle bore
|
4-jaw independent chuck
|
Spindle nose DIN 55027
|
Face plate without jaws
|
El. Cabinet with control panel
|
Follow rest
|
Centralized lubrication system
|
Steady rest
|
Coolant system with pump
|
Digital Read Out
|
Low voltage machine lamp 12V
|
One position longitudinal stop
|
Monolith cast iron body and gap
|
Thread chasing dial
|
Back plate for universal chuck
|
Taper turning attachment
|
Full length rear splash guard
|
Drive plate with turnning dogs
|
Tool holder protection screen
|
Live (rotating) centre
|
Splash guard for the chuck
|
Drill chuck
|
Protection of the lead shaft and screw
|
Foot brake pedal
|
“V” belts set
|
Increasing of the main motor power
|
Leveling bolts – set
|
Quck chabge tool post MultiFix
|
Hexagonal wrenches set
|
Electro-dynamic brake
|
Dead centre for spindle
|
Tailstock dead centre
|
Reduction sleeve for the spindle
|
Reduction sleeve for the tailstock
|
Rapid traverse of the apron in 4 directions
|
Cam-lock spindle execution
|